This OUTDOOR RATED (IP66), REGULAR-DUTY, 22AWG, 6.5-ft (2m) long DC power cable can handle up to 2A of current. This outdoor cable has an M12-1.75, 5.5mm x 2.1mm male barrel plug at one end of the cable, and the other end of the cable has a pair of 2mm bare conductors (see illustrations) that are tinned and ready to be soldered to the appropriate points in an electronic circuit. This outdoor power cable is intended for the do-it-yourselfer with the equipment and skills necessary to solder the stripped and tinned bare ends of the cable to the appropriate points in an electronic circuit. The most common application of this outdoor cable is to replace an existing power cable on a solar panel since most solar panels on the market do not have outdoor rated (IP66) power cables. Most solar panels on the market have simple “push-to-connect” type 5.5mm x 2.1mm male barrel plugs which allow water and dirt to penetrate which eventually leads to an unreliable connection due to corrosion and degradation of the electrical connection between barrel connectors. The M12-1.75, 5.5mm x 2.1mm male barrel plug at one end of this outdoor rated cable creates a weatherproof seal when the M12-1.75 screw connector is mated with an appropriate M12-1.75, 5.5mm x 2.1mm female barrel socket. A weatherproof seal is created by compression of the rubber O-ring on the M12-1.75, 5.5mm x 2.1mm male barrel plug when mated with the appropriate M12-1.75, 5.5mm x 2.1mm female barrel socket (refer to illustrations) such as those found on our outdoor rated battery eliminator kits and outdoor accessories such as our outdoor power extension cables, outdoor power splitter cables, and outdoor active dummy cell batteries. This outdoor power cable can also serve as a replacement of the power cables found on our outdoor solar panels and modules.

This connector adapter has a regular USB type-A female socket on one end and a 5.5mm x 2.1mm female barrel socket the other end. This adapter is used to convert a 5.5mm x 2.1mm male barrel plug to a regular USB type-A female socket. Great for converting the typical 5.5mm x 2.1mm male barrel plug at the end of the power cable found on many AC to DC wall power adapters to a regular USB type-A female socket power source (see WARNING). See pictures for an illustration of this typical application. The 5.5mm x 2.1mm female barrel socket at one end of connector adapter works with the 5.5mm x 2.1mm male barrel plugs found on our battery eliminator kit accessories such as our power extension cables, power splitter cables and AC to DC wall power adapters. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a micro-USB male plug on one end and a 5.5mm x 2.1mm female barrel socket at the other end. This adapter is used to convert a 5.5mm x 2.1mm male barrel plug to a micro-USB male plug. Great for converting a 5.5mm x 2.1mm male barrel plug on a power source such as an AC/DC wall power adapter (see WARNING) to a micro-USB male plug. See pictures for an illustration of a typical application. The 5.5mm x 2.1mm female barrel socket at one end of this connector adapter works with the 5.5mm x 2.1mm male barrel plugs found on our battery eliminator kit accessories such as our AC/DC wall power adapters, power extension cables, and power splitter cables. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a micro-USB male plug on one end and a USB C female socket at the other end. This adapter is used to convert a USB C male plug to a micro-USB male plug. Great for converting a USB C male plug on a power source such as an AC/DC wall power adapter (see WARNING) to a micro-USB male plug. See pictures for an illustration of a typical application. This connector adapter supports power and USB 2.0 data transmission rates (480Mbps).

This connector adapter has a USB C male plug on one end and a 5.5mm x 2.1mm female barrel socket at the other end. This adapter is used to convert a 5.5mm x 2.1mm male barrel plug to a USB C male plug. Great for converting a 5.5mm x 2.1mm male barrel plug on a power source such as an AC/DC wall power adapter (see WARNING) to a USB C male plug. See pictures for an illustration of a typical application. The 5.5mm x 2.1mm female barrel socket at one end of this connector adapter works with the 5.5mm x 2.1mm male barrel plugs found on our battery eliminator kit accessories such as our AC/DC wall power adapters, power extension cables, and power splitter cables. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a USB C male plug on one end and a micro-USB female socket at the other end. This adapter is used to convert a micro-USB male plug to a USB C male plug. Great for converting a micro-USB male plug on a power source such as an AC/DC wall power adapter (see WARNING) to a USB C male plug. See pictures for an illustration of a typical application. This connector adapter supports power and USB 2.0 data transmission rates (480Mbps).

This connector adapter has a regular USB type-A male plug on one end and a 5.5mm x 2.1mm male barrel plug the other end. This adapter is used to convert a regular USB type-A female socket to a 5.5mm x 2.1mm male barrel plug. Great for converting a regular USB type-A female socket on a USB power source to a 5.5mm x 2.1mm male barrel plug (see WARNING). See pictures for an illustration of this typical application. The 5.5mm x 2.1mm male barrel plug at one end of the connector adapter works with the 5.5mm x 2.1mm female barrel sockets found on our battery eliminator kit accessories such as our active dummy cell batteries, power extension cables, and power splitter cables. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a USB C female socket on one end and a 5.5mm x 2.1mm male barrel plug at the other end. This adapter is used to convert a USB C male plug to a 5.5mm x 2.1mm male barrel plug. Great for converting a USB C male plug on a power source such as an AC/DC wall power adapter (see WARNING) to a 5.5mm x 2.1mm male barrel plug. See pictures for an illustration of a typical application. The 5.5mm x 2.1mm male barrel plug at one end of this connector adapter works with the 5.5mm x 2.1mm female barrel sockets found on our battery eliminator kit accessories such as our active dummy cell batteries, power extension cables, and power splitter cables. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a micro-USB female socket on one end and a 5.5mm x 2.1mm male barrel plug at the other end. This adapter is used to convert a micro-USB male plug to a 5.5mm x 2.1mm male barrel plug. Great for converting a micro-USB male plug on a power source such as an AC/DC wall power adapter (see WARNING) to a 5.5mm x 2.1mm male barrel plug. See pictures for an illustration of a typical application. The 5.5mm x 2.1mm male barrel plug at one end of this connector adapter works with the 5.5mm x 2.1mm female barrel sockets found on our battery eliminator kit accessories such as our active dummy cell batteries, power extension cables, and power splitter cables. This connector adapter only supports power and does not support USB data transmission.

This connector adapter has a 5.5mm x 2.1mm female barrel socket on one end and a 3.5mm x 1.35mm male barrel plug on the other end. This adapter is used to convert a 5.5mm x 2.1mm male barrel plug to a 3.5mm x 1.35mm male barrel plug. Great for converting the typical 5.5mm x 2.1mm male barrel plug at the end of the power cable found on many AC to DC wall power adapters to a 3.5mm x 1.35mm male barrel plug for electronic devices that have this type of mini female barrel socket input used for powering or charging the device. See pictures for an illustration of this typical application. The 5.5mm x 2.1mm female barrel socket at one end of connector adapter works with the 5.5mm x 2.1mm male barrel plugs found on our battery eliminator kit accessories such as our power extension cables, power splitter cables and AC to DC wall power adapters.

This 6" long right-angle adapter cable allows you to convert a straight 5.5mm x 2.1mm barrel plug to a right-angle (90-degree) 5.5mm x 2.1mm barrel plug. Perfect for those odd applications where a right-angle barrel plug is needed. The cable has a straight 5.5mm x 2.1mm barrel socket at one end and a right-angle (90-degree) 5.5mm x 2.1mm plug at the other end. This cable works with the 5.5mm x 2.1mm barrel connectors on our battery eliminator kits and accessories such as our power extension cables, power splitter cables, AC to DC wall power adapters and our active dummy cell batteries.

This Thin Flat Flexible Cable (FFC) has 2 x 24AWG conductors and is 5.08mm wide, 7.5” long and only 0.22mm thick. One end of the cable has a 2.1mm ID x 5.5mm OD over-mold in-line female barrel socket DC power connector, and the other end has 4mm of bare conductors that are tinned and ready to be soldered to a connector of your choice or directly to the appropriate points in an electronic circuit. Since this cable is extremely thin and flexible, it can be run around battery compartment covers, through narrow cracks and around tight corners, and it can also be run under items allowing them to sit flat without tilting or wobbling. The cable polarity is indicated with a white mark on the insulation of the FFC cable. This white mark indicates the conductor that is attached to the center conducting pin on the 2.1mm x 5.5mm female barrel socket connector. The female barrel socket connector is made of a black PVC insulating material, and the FFC cable is made of black polyester insulating material.

This White Thin Flat Flexible Cable (FFC) has 2 x 24AWG conductors and is 5.08mm wide, 7.5” long and only 0.22mm thick. One end of the cable has a 2.1mm ID x 5.5mm OD over-mold in-line female barrel socket DC power connector, and the other end has 4mm of bare conductors that are tinned and ready to be soldered to a connector of your choice or directly to the appropriate points in an electronic circuit. Since this cable is extremely thin and flexible, it can be run around battery compartment covers, through narrow cracks and around tight corners, and it can also be run under items allowing them to sit flat without tilting or wobbling. The cable polarity is indicated with a faint red stripe on the insulation of the FFC cable. This faint red stripe indicates the conductor that is attached to the center conducting pin on the 2.1mm x 5.5mm female barrel socket connector. The female barrel socket connector is made of a white PVC insulating material, and the FFC cable is made of a white polyester insulating material.

This LIGHT-DUTY, 24AWG, 6-ft (1.83m) long power extension cable can handle up to 1A of current and is great for adding additional length to existing power cables that are used for charging or powering electronic devices from +5VDC USB wall power adapters or other +5VDC USB power sources. This cable has a regular USB Type-A plug at one end and a 5.5mm x 2.1mm male barrel plug at the other end. Perfect for adapting existing +5VDC USB power output ports to our 3-cell battery eliminator kits (AAA, AA, C and D cell). The 5.5mm x 2.1mm male barrel plug at one end of the cable works with the barrel connector sockets on our 3-cell battery eliminator kits and other battery eliminator kit accessories such as our power extension cables and power splitter cables. This cable only supports power and does not support USB data transmission.

This REGULAR-DUTY, 22AWG, 3.3-ft (1m) long right-angle power extension cable can handle up to 2A of current and is great for adding additional length to existing power cables that are used for charging or powering electronic devices from +5VDC USB wall power adapters or other +5VDC USB power sources. This cable has a regular USB Type-A plug at one end and a right-angle 5.5mm x 2.1mm male barrel plug at the other end. Perfect for adapting existing +5VDC USB power output ports to our 3-cell battery eliminator kits (AAA, AA, C and D cell). The right-angle 5.5mm x 2.1mm male barrel plug at one end of the cable works with the barrel connector sockets on our 3-cell battery eliminator kits and other battery eliminator kit accessories such as our power extension cables and power splitter cables. The right-angle 5.5mm x 2.1mm male barrel plug is great for use in narrow or tight spaces. This cable only supports power and does not support USB data transmission.

This LIGHT-DUTY, 24AWG, 3.3-ft (1m) long power extension cable can handle up to 1A of current and is great for adding additional length to existing power cables that are used for charging or powering electronic devices from +5VDC USB wall power adapters or other +5VDC USB power sources. This cable has a regular USB Type-A plug at one end and a 3.5mm x 1.35mm mini male barrel plug at the other end. Perfect for adapting existing +5VDC USB power output ports to electronic devices that have a 3.5mm x 1.35 mini female barrel socket. This cable only supports power and does not support USB data transmission.

This 12in (30cm) long USB power splitter cable allows you to power or charge up to 2 x electronic devices from a single +5VDC USB wall power adapter or other +5VDC USB power source. This power splitter cable has a single regular USB Type-A male plug at one end of the cable and 2 x regular Type-A female sockets at the other end of the cable. This power splitter cable works with our 3-cell (+5VDC) battery eliminator kits and other battery eliminator kit accessories such as our power extension cables and power splitter cables provided they have the appropriate USB connectors or the appropriate USB connector conversion adapters.

This 3.3-ft (1m) long USB power splitter cable allows you to power or charge up to 3 x electronic devices from a single +5VDC USB wall power adapter or other +5VDC USB power source. This power splitter cable has a single regular USB Type-A male plug at one end of the cable and 3 x regular Type-A female sockets at the other end of the cable. This power splitter cable works with our 3-cell (+5VDC) battery eliminator kits and other battery eliminator kit accessories such as our power extension cables and power splitter cables provided they have the appropriate USB connectors or the appropriate USB connector conversion adapters.

This 3-way HEAVY-DUTY 6'9" long power splitter & extension cable allows you to power up to 3 x LED flameless LED candles or other electronic devices from a single AC to DC wall power adapter. The length of each branch of the cable is 6'2" long and a 2-position ON/OFF rocker switch is built into the common branch of the cable allowing you to turn “On” and “Off” the electronic devices with the flip of a switch! The cable's HEAVY-DUTY construction uses large gauge wire to reduce the voltage drops across the cable meaning more power gets delivered to your electronic devices. This power splitter cable has a single 5.5mm x 2.1mm barrel plug at the common end of the cable and a 5.5mm x 2.1mm barrel socket at the other end of each branch of the cable. This power splitter cable works with the barrel connectors on our battery eliminator kits and accessories such as our power extension and power splitter cables, AC to DC wall power adapters and our active dummy cell batteries.

This 20.5in (52.1cm) long USB power splitter cable allows you to charge up to 6 x electronic devices from a single +5VDC USB wall power adapter or other +5VDC USB power source. This power splitter cable has a single regular USB Type-A male plug at one end of the cable and 6 x regular Type-A female sockets at the other end of the cable. This power splitter cable works with our 3-cell (+5VDC) battery eliminator kits and other battery eliminator kit accessories such as our power extension cables and power splitter cables provided they have the appropriate USB connectors or the appropriate USB connector conversion adapters.

Great for protecting the connectors on our indoor power extension and indoor power splitter cables from water, chemicals and dirt allowing them to be used outdoors! This small piece of black dual-wall heat shrink tubing is 1-inch long and has a 0.5-inch non-recovered diameter and 1/8-Inch recovered diameter. The tubing has an adhesive lined inner wall that activates once heated and creates a tough water, dirt, and chemical resistant bond after recovering from being heated. The tubing has a large 4:1 heat-shrink ratio allowing for a snug fit over rough and uneven surfaces. This piece of heat-shrink tubing is the perfect length and diameter to fit over our indoor 5.5mm x 2.1mm barrel connectors to create a water, chemical and dirt resistant barrier. It will also work with connections between an indoor 5.5mm x 2.1mm barrel connector and an outdoor (IP66 rated) 5.5mm x 2.1mm barrel connector with M12-1.75 threads. This tubing can also be used for other types of connectors such as adapters used to convert from 5.5mm x 2.1mm barrel connectors to USB and other types of miniature connectors. The tubing can be shrunk using a heat gun, a hair dryer and even an open flame from a lighter or a match. Made of flame-retardant materials.